P1214 FORD Possible Causes

• Faulty pedal position sensor
• Pedal position sensor harness is open or shorted
• Poor electrical connection in the pedal position sensor circuit

How to Fix Code P1214 FORD?

Start by checking the “possible causes” listed above. Visually inspect the corresponding wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector pins.

Possible Symptoms

• Engine light on (or service engine soon warning light)

P1214 FORD Meaning

Pedal Position Sensor B Circuit Intermittent is the generic description for Ford code P1214, but the manufacturer may have a different description for your vehicle’s model and year. Currently, we do not have more information about the Ford P1214 OBDII code.

P1214 GMC Possible Causes

• Fuel injection pump gear alignment
• Fuel filter restriction
• Transfer pump inlet restriction
• Faulty fuel injection pump

How is GMC P1214 Code Repaired?

Start by checking the “possible causes” listed above. Visually inspect the related wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector pins.

Technical Notes

The Diagnostic Trouble Code (DTC) P1214 is stored in memory after installing a replacement ECC or replacing the fuel injection pump.
Perform the Top Dead Center (TDC) offset procedure to ensure proper injection pump timing. Follow the procedure below:
1. First, perform the Passlock anti-theft relearn procedure.
2. Install a suitable scan tool.
3. Using the scan tool, clear any existing DTCs.
4. Start the engine and bring it to operating temperature. Stop the engine.
5. Turn the ignition switch to the ON position, engine off (not running).
6. Fully depress the accelerator for at least 45 seconds.
7. Turn the ignition switch to the OFF position for 30 seconds.
8. Restart the engine. Using the scan tool, verify that the TDC offset has been reset.
9. Start the engine and bring it to operating temperature, engine speed below 1500 RPM.
10. Using the scan tool, check that the TDC offset is between -0.25 and -0.75. If the TDC offset is within specifications, the relearn procedure is complete. 11. If the TDC is not within specifications, it will be necessary to reset the
injection pump timing. Follow the procedure described in the service manual.

Possible Symptoms

• Engine light on (or engine service soon warning light)

P1214 GMC Meaning

The Powertrain Control Module (PCM) monitors the crankshaft position via the Crankshaft Position Sensor (CKP). The CKP information is used to determine the amount of injection timing offset required for proper operation. This code will set if the TDC offset is greater than +2.46 degrees or less than -2.46 degrees. It looks like you need to perform a TDC offset learning procedure.

P1214 MINI Possible Causes

• Faulty fuel pump
• Fuel pump wiring harness is open or shorted
• Poor electrical connection in the fuel pump circuit

How to Fix P1214 MINI Code?

Start by checking the “possible causes” listed above. Visually inspect the corresponding wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector pins.

Possible Symptoms

• Engine light on (or engine service warning light soon)

P1214 MINI Meaning

Fuel pump is the generic description for the P1214 Mini code, but the manufacturer may have a different description for your vehicle model and year. Currently, we do not have more information about the P1214 Mini OBDII code.

P1214 VOLKSWAGEN Possible Causes

• Faulty fuel injector
• Fuel injector harness is open or shorted
• Poor electrical connection in fuel injector circuit

How to Fix Code P1214 VOLKSWAGEN?

Start by checking the “possible causes” listed above. Visually inspect the corresponding wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector pins.

Possible Symptoms

• Engine light on (or service engine soon warning light)

P1214 VOLKSWAGEN Meaning

Cylinder 2 Injector Circuit Short to Positive is the generic description for Volkswagen code P1214, but the manufacturer may have a different description for your vehicle model and year. Currently, we have no further information about Volkswagen OBDII code P1214.

P1215 Possible Causes

• Faulty Electronic Drive Unit (EDU)
• Electronic Drive Unit (EDU) harness is open or shorted
• Poor electrical connection in Electronic Drive Unit (EDU) circuit
• Faulty spill control valve

How to Fix Code P1215?

Start by checking the “Possible Causes” listed above. Visually inspect the corresponding wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector pins.

Possible Symptoms

• Engine light on (or service engine soon warning light)

P1215 Meaning

The Electronic Drive Unit (EDU) drives the spill control valve at high speeds. The high-speed operation of the EDU under high fuel pressure conditions is achieved through the use of a DC/DC converter that provides a high-voltage quick charging system.
The Engine Control Unit (ECU) continuously monitors the EDU and stops the engine if an abnormal condition is detected.
The battery voltage is increased by the DC/DC converter. A voltage of approximately 50 V is applied to the spill control valve according to the IJ+ signal received from the engine ECU. At this time, the injection verification signal (IJF) is sent to the engine ECU.

P1215 AUDI Possible Causes

• Faulty fuel injector
• Fuel injector harness is open or shorted
• Poor electrical connection in fuel injector circuit

How to Fix P1215 AUDI Code?

Start by checking the “possible causes” listed above. Visually inspect the corresponding wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector pins.

Possible Symptoms

• Engine light on (or service engine soon warning light)

P1215 AUDI Meaning

Cylinder 3 Injector Circuit Short to Positive is the generic description for Audi P1215 code, but the manufacturer may have a different description for your vehicle model and year. Currently, we don’t have more information about the Audi P1215 OBDII code.

P1215 BMW Possible Causes

• Faulty fuel pump
• Fuel pump harness is open or shorted
• Poor electrical connection in the fuel pump circuit

How to Fix BMW P1215 Code?

Start by checking the “possible causes” listed above. Visually inspect the corresponding wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector pins.

Possible Symptoms

• Engine light on (or service engine soon warning light)

P1215 BMW Meaning

Fuel pump is the generic description for Bmw P1215 code, but the manufacturer may have a different description for your vehicle model and year. Currently, we do not have more information about the P1215 Bmw OBDII code.

P1215 FORD Possible Causes

• Faulty pedal position sensor
• Pedal position sensor harness is open or shorted
• Poor electrical connection in the pedal position sensor circuit

How to Fix Code P1215 FORD?

Start by checking the “possible causes” listed above. Visually inspect the corresponding wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector pins.

Possible Symptoms

• Engine light on (or service engine soon warning light)

P1215 FORD Meaning

The low input of the “C” pedal position sensor circuit is the generic description for Ford code P1215, but the manufacturer may have a different description for your vehicle model and year. Currently, we do not have more information about the Ford P1215 OBDII code.

P1215 GMC Possible Causes

• Faulty generator driver
• Generator driver circuit is open or shorted
• Poor electrical connection in the generator control circuit

How to Fix GMC Code P1215?

Start by checking the “possible causes” listed above. Visually inspect the corresponding wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector pins.

Possible Symptoms

• Engine light on (or engine service warning light soon)

P1215 GMC Meaning

With the engine running, the Powertrain Control Module (PCM) determines that the generator FET driver has failed.

P1215 LEXUS Possible Causes

• Faulty Electronic Drive Unit (EDU)
• Electronic Drive Unit (EDU) harness is open or shorted
• Poor electrical connection in Electronic Drive Unit (EDU) circuit
• Defective spill control valve

How to Fix P1215 LEXUS Code?

Start by checking the “possible causes” listed above. Visually inspect the corresponding wiring harness and connectors. Look for damaged components and check for broken, bent, pushed out, or corroded connector pins.

Possible Symptoms

• Engine light on (or engine service warning light soon)

P1215 LEXUS Meaning

The Electronic Drive Unit (EDU) drives the spill control valve at high speeds. The high-speed operation of the EDU under high fuel pressure conditions is achieved through the use of a DC/DC converter that provides a high-voltage quick charging system.
The engine Electronic Control Unit (ECU) continuously monitors the EDU and stops the engine if an abnormal condition is detected.
The battery voltage is increased by the DC/DC converter. A voltage of approximately 50 V is applied to the spill control valve according to the IJ+ signal received from the engine ECU. At this time, the injection check signal (IJF) is sent to the engine ECU.