B0010 LINCOLN Possible Causes

• Faulty passenger airbag
• Passenger airbag harness is open or short-circuited
• Poor electrical connection in the passenger airbag circuit

How to Fix B0010 LINCOLN Code?

Start by checking the “possible causes” listed above. Visually inspect the wiring harness and corresponding connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector pins.

When is the Code Detected?

If the Restraints Control Module (RCM) detects a short circuit between the passenger airbag stage 1 circuits and the circuits of another SRS component, it sets this Diagnostic Trouble Code (DTC) and the corresponding SRS component DTC.

Possible Symptoms

Airbag warning light illuminated

B0010 LINCOLN Meaning

The Restraints Control Module (RCM) monitors all deployable device and sensor circuits for a coupled signal (short) between circuits. If the RCM detects a short circuit between the circuits of one device and another device, it will store a DTC for each of the signal cross-coupling faults in memory. The RCM sends a message to the instrument panel cluster (IPC) to illuminate the airbag warning indicator. When a normal loop fault is present (a loop is either shorted to battery/ground, open circuit, or low resistance), then the signal cross-coupling diagnostic will not be active. Once the normal loop fault is repaired, the signal cross-coupling diagnostic resumes.

B0010 MERCURY Possible Causes

• Faulty passenger airbag
• Passenger airbag harness is open or short-circuited
• Poor electrical connection in the passenger airbag circuit

How to Fix B0010 MERCURY Code?

Start by checking the “possible causes” listed above. Visually inspect the corresponding wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector pins.

When is the Code Detected?

If the Restraints Control Module (RCM) detects a short circuit between the passenger airbag stage 1 circuits and the circuits of another SRS component, it sets this Diagnostic Trouble Code (DTC) and the corresponding SRS component DTC.

Possible Symptoms

Airbag warning light illuminated

B0010 MERCURY Meaning

The Restraints Control Module (RCM) monitors all deployable device and sensor circuits for a coupled signal (short) between circuits. If the RCM detects a short circuit between the circuits of one device and another device, it will store a DTC for each of the signal cross-coupling faults in memory. The RCM sends a message to the instrument panel cluster (IPC) to illuminate the airbag warning indicator. When a normal loop fault is present (a loop is either shorted to battery/ground, open circuit, or low resistance), then the signal cross-coupling diagnostic will not be active. Once the normal loop fault is repaired, the signal cross-coupling diagnostic resumes.

B0010 NISSAN Possible Causes

• Faulty passenger airbag module
• Passenger airbag module wiring harness is open or short-circuited
• Poor electrical connection in the passenger airbag module circuit
• Faulty airbag diagnostic sensor unit

How to Fix B0010 NISSAN Code?

Start by checking the “possible causes” listed above. Visually inspect the corresponding wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector pins.

Possible Symptoms

Airbag warning light illuminated

B0010 NISSAN Meaning

The passenger airbag module is either dual-stage or single-stage and is wired to the airbag diagnostic sensor unit. The airbag diagnostic sensor unit will monitor for opens and shorts in the detected lines to the passenger airbag module.

B0011 Possible Causes

• Faulty passenger airbag
• Passenger airbag harness is open or short-circuited
• Poor electrical connection in the passenger airbag circuit

How is B0011 Code Repaired?

Start by checking the “Possible Causes” listed above. Visually inspect the corresponding wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector pins.

When is the Code Detected?

If the Restraint Control Module (RCM) detects a short circuit between the passenger airbag stage 2 circuits and the circuits of another SRS component, it sets this Diagnostic Trouble Code (DTC) and the corresponding SRS component DTC.

Possible Symptoms

Airbag warning light illuminated

B0011 Meaning

The Restraint Control Module (RCM) monitors all deployable device and sensor circuits for a coupled signal (short) between circuits. If the RCM detects a short circuit between the circuits of one device and another device, it will store a DTC for each of the signal cross-coupling faults in memory. The RCM sends a message to the instrument panel cluster (IPC) to illuminate the airbag warning indicator. When a normal loop fault is present (a loop is either shorted to battery/ground, open circuit, or low resistance), then the signal cross-coupling diagnostics will not be active. Once the normal loop fault is repaired, the signal cross-coupling diagnostic resumes.

B0011 ACURA Possible Causes

• Faulty passenger side airbag
• Passenger side airbag harness is open or short-circuited
• Poor electrical connection in passenger side airbag circuit
• Faulty steering wheel clock spring

How to Fix B0011 ACURA Code?

Start by checking the “possible causes” listed above. Visually inspect the corresponding wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector pins.

Symptoms

Possible

Airbag warning light illuminated

B0011 ACURA Meaning

The driver side airbag is located in the center of the steering wheel. The front passenger side airbag is located in the front passenger side dashboard. The airbag modules adopt dual inflators for the driver side and/or front passenger side airbag according to specifications. The dual inflators enhance airbag effectiveness by properly adjusting the timing when both inflators are activated (simultaneously or sequentially) based on collision speed or impact severity.

B0011 CHRYSLER Possible Causes

• Faulty passenger airbag
• Passenger airbag harness is open or shorted
• Poor electrical connection in the passenger airbag circuit
• Faulty Occupant Restraint Controller (ORC)

How to Fix B0011 CHRYSLER Code?

Start by checking the “possible causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector pins.

Possible Symptoms

Airbag warning light illuminated

B0011 CHRYSLER Meaning

When powered on, the Occupant Restraint Controller (ORC) sends a test current to the squibs to verify the integrity of the squib and wiring. These circuits are maintained in a floating configuration at the ORC (neither connected to power nor ground) as protection against accidental deployment. Using the Supplemental Restraint System (SRS) load tool in the tests below replaces a suspected squib with a known good component. Using the SRS load tool adapter provides a test point as well as a method to open the shorting bar connections in the ORC harness connector.

B0011 DODGE Possible Causes

• Faulty passenger airbag
• Passenger airbag harness is open or short-circuited
• Poor electrical connection in the passenger airbag circuit
• Faulty Occupant Restraint Controller (ORC)

How to Fix B0011 DODGE Code?

Start by checking the “possible causes” listed above. Visually inspect the corresponding wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector pins.

Possible Symptoms

Airbag warning light illuminated

B0011 DODGE Meaning

When powered on, the Occupant Restraint Controller (ORC) sends a test current to the squibs to verify the integrity of the squib and wiring. These circuits are maintained in a floating configuration at the ORC (neither connected to power nor ground) as protection against accidental deployment. Using the Supplemental Restraint System (SRS) load tool in the tests below replaces a suspected squib with a known good component. Using the SRS load tool adapter provides a test point as well as a method to open the shorting bar connections in the ORC harness connector.

B0011 FORD Possible Causes

• Faulty passenger airbag
• Passenger airbag harness is open or short-circuited
• Poor electrical connection in the passenger airbag circuit

How to Fix B0011 FORD Code?

Start by checking the “possible causes” listed above. Visually inspect the wiring harness and corresponding connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector pins.

When is the Code Detected?

If the Restraints Control Module (RCM) detects a short circuit between the passenger airbag stage 2 circuits and the circuits of another SRS component, it sets this Diagnostic Trouble Code (DTC) and the corresponding SRS component DTC.

Possible Symptoms

Airbag warning light illuminated

B0011 FORD Meaning

The Restraints Control Module (RCM) monitors all deployable device and sensor circuits for a coupled (shorted) signal between circuits. If the RCM detects a short circuit between the circuits of one device and another device, it will store a DTC for each of the signal cross-coupling faults in memory. The RCM sends a message to the instrument panel cluster (IPC) to illuminate the airbag warning indicator. When a normal loop fault is present (a loop is either shorted to battery/ground, open circuit, or low resistance), then the signal cross-coupling diagnostics will not be active. Once the normal loop fault is repaired, the signal cross-coupling diagnostic resumes.

B0011 HONDA Possible Causes

• Faulty passenger side airbag
• Passenger airbag harness is open or short-circuited
• Poor electrical connection in the passenger side airbag circuit

How to Fix B0011 HONDA Code?

Start by checking the “possible causes” listed above. Visually inspect the corresponding wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector pins.

Possible Symptoms

Airbag warning light illuminated

B0011 HONDA Meaning

The driver side airbag is located in the center of the steering wheel. The front passenger airbag is located in the front passenger side dashboard. Airbag modules adopt dual inflators for the driver side and/or front passenger airbag according to specifications. Dual inflators enhance airbag effectiveness by properly adjusting timing when both inflators are activated (simultaneously or sequentially) based on collision speed or impact severity.

B0011 INFINITI Possible Causes

• Faulty passenger airbag module
• Passenger airbag module harness is open or shorted
• Poor electrical connection in passenger airbag module circuit
• Faulty airbag diagnostic sensor unit

How to Fix B0011 INFINITI Code?

Start by checking the “Possible Causes” listed above. Visually inspect the related wiring harness and connectors. Check for damaged components and look for broken, bent, pushed out, or corroded connector pins.

Possible Symptoms

Airbag warning light illuminated

B0011 INFINITI Meaning

The passenger airbag module is dual-stage or single-stage and is wired to the airbag diagnostic sensor unit. The airbag diagnostic sensor unit will monitor for opens and shorts in the detected lines to the passenger airbag module.