What does it mean?
This is a generic diagnostic trouble code (DTC) and generally applies to OBD-II equipped vehicles with an automatic transmission.
This can include, but is not limited to, vehicles from Chrysler, Ford, Dodge, Hyundai, Kia, Ram, Lexus, Toyota, Mazda, Honda, VW, etc. Although generic, the exact repair steps may vary depending on the year, make, model, and powertrain configuration.
Most automatic transmissions incorporate a number of shift solenoids, depending on the number of gears inside. The related fault codes for the “G” shift solenoid are P075A, P075B, P075C, P075D, and P075E, depending on the specific malfunction that alerts the PCM to set the code and illuminate the Check Engine light. If you have an Overdrive light or other transmission warning light, it may also be illuminated.
The purpose of the shift solenoid circuit is for the PCM to monitor the shift solenoids to manage the movement of fluid between different hydraulic circuits and change the gear ratio at the appropriate time. This process maximizes engine performance at the lowest possible RPM.
The automatic transmission relies on bands and clutches to shift gears, and this is accomplished by having fluid pressure in the right place at the right time. The transmission solenoids are responsible for opening or closing valves in the valve body to allow transmission fluid to flow to the clutches and bands, enabling smooth transmission operation as the engine accelerates.
When the Powertrain Control Module (PCM) detects a malfunction in the “G” shift solenoid circuit, a variety of codes can be triggered depending on the specific vehicle, transmission, and the number of gears in the specific automatic transmission. In this case, the OBD-II fault code P075A is associated with a general malfunction in the “G” transmission shift solenoid circuit.
How severe is this DTC?
The severity of this code normally starts as moderate but can escalate to a more severe level quickly if not corrected in a timely manner.
What are some of the symptoms of the code?
Symptoms of a P075A fault code may include:
Transmission slipping
Transmission overheating
Transmission shifting harshly
Reduced fuel economy
Symptoms
potentially missed shifts
Vehicle enters limp mode
Check Engine light illuminated
What are some common causes of the code?
Causes
of this P075A transmission code may include:
Low fluid level
Dirty or contaminated fluid
Dirty or clogged transmission filter
Faulty transmission valve body
Restricted hydraulic passages
Transmission has an internal failure
Faulty shift solenoid
Corroded or damaged connector
Faulty or damaged wiring
Faulty PCM
What are the troubleshooting steps for P075A?
Before starting the troubleshooting process for any malfunction, you should research the Technical Service Bulletins (TSBs) for the specific vehicle by year, model, and transmission. In some circumstances, this can save you a lot of time in the long run by pointing you in the right direction. You should also check the vehicle’s records to verify the last time the filter and fluid were changed, if possible.
Fluid and Wiring Inspections
The first step is to ensure the fluid level is correct and inspect the condition of the fluid for any contamination. Next, a thorough visual inspection should be performed to check the associated wiring for obvious defects such as scraping, rubbing, bare wires, or burn spots.
Then, check the connectors and connections for security, corrosion, and damaged pins. This process should include all wiring and connectors for the transmission solenoids, transmission pump, and PCM. Depending on the configuration, the transmission grounding should be inspected for security and bonding issues.
Advanced Steps
Advanced steps become very vehicle-specific and require appropriate advanced equipment to perform accurately. These procedures require a digital multimeter and the vehicle-specific technical references. Voltage requirements will be highly dependent on the specific year and model of the vehicle. You must follow the troubleshooting chart specific to your vehicle.
Continuity Checks
Continuity checks should always be performed with the power disconnected from the circuit, and normal readings for wiring and connections should be 0 ohms of resistance, unless otherwise specified by the technical data. Resistance or lack of continuity indicates faulty wiring that is open or shorted and must be repaired or replaced.
What are the common repairs for this code?
Replacing fluid and filter
Repairing or replacing a faulty shift solenoid
Repairing or replacing the faulty transmission valve body
Repairing or replacing the faulty transmission
Flushing the transmission to clean passages
Cleaning corrosion from connectors
Repairing or replacing wiring
Reprogramming or replacing the PCM
I hope the information in this article has been helpful in guiding you in the right direction to correct the issue with your shift solenoid circuit error code. This article is strictly informational, and the technical data and service bulletins specific to your vehicle should always take priority.