What does it mean?
This generic powertrain/engine diagnostic code generally applies to all OBD-II equipped vehicles, including but not limited to Nissan, Dodge, Chrysler, Honda, Chevrolet, GMC, Toyota, etc., but seems to be most commonly seen on Nissan vehicles.
The Transmission Fluid Pressure Sensor/Switch (TFPS) is typically found attached to the side of the valve body inside the transmission, although sometimes it may be found screwed into the side of the transmission case/body itself.
The TFPS converts mechanical transmission pressures into an electrical signal for the Powertrain Control Module (PCM) or Transmission Control Module (TCM). Typically, the PCM/TCM will then inform other controllers using the vehicle’s data communication bus.
The PCM/TCM receives this voltage signal to determine transmission operating pressure or when a shift occurs. This code is set if this “G” input does not match the normal operating voltages stored in the PCM/TCM memory. This may also be due to internal mechanical problems inside the transmission. Refer to a vehicle-specific repair manual to determine what the “G” circuit is for your particular vehicle.
P083A is typically an electrical circuit problem (TFPS sensor circuit), although, as mentioned earlier, this code may also be set due to mechanical issues (internal leaks, cracked or missing control balls in the valve body, low system operating pressure/main line pressure, stuck valve in the valve body). This cannot be ignored in the troubleshooting phase, especially when dealing with an intermittent issue.
Troubleshooting steps may vary depending on the manufacturer, TFPS sensor type, and wire colors.
Related “G” Transmission Fluid Pressure Sensor Circuit Codes:
P083B Transmission Fluid Pressure Sensor/Switch “G” Circuit Range/Performance
P083C Transmission Fluid Pressure Sensor/Switch “G” Circuit Low
P083D Transmission Fluid Pressure Sensor/Switch “G” Circuit High
P083E Transmission Fluid Pressure Sensor/Switch “G” Circuit Intermittent
Code Severity and Symptoms
Severity depends on the circuit where the failure occurred. Since it is an electrical failure, the PCM/TCM may compensate to some extent. The failure may mean the PCM/TCM alters transmission shifting if it is electronically controlled.
Symptoms of a P083A engine code may include:
Malfunction Indicator Light illuminated
Change in shift quality
Vehicle starts in 2nd or 3rd gear (limp mode)
Causes
Typically, the causes for this code to be set are as follows:
Open in the signal circuit to the TFPS sensor – possible
Short to voltage in the signal circuit to the TFPS sensor – possible
Short to ground in the signal circuit to the TFPS sensor – possible
Faulty TFPS sensor – probable
Internal mechanical transmission problem – possible
Failed PCM – unlikely (programming required after replacement)
Diagnostic and Repair Procedures
A good starting point is always to check the Technical Service Bulletins (TSBs) for your particular vehicle. Your problem may be a known issue with a known fix published by the manufacturer and can save you time and money when diagnosing.
A good example of this would be if there are known power-related codes set with P083A, or if there is more than one set of pressure sensor/switch codes. If so, begin your diagnosis with the power-related trouble code or multiple code diagnosis first, as this may be the reason for P083A.
Next, locate the Transmission Fluid Pressure Sensor/Switch (TFPS) on your particular vehicle. The TFPS is typically found attached to the side of the valve body inside the transmission, although it is sometimes screwed into the side of the transmission case/body itself. Once located, visually inspect the connector and wiring. Look for chafing, rubbing, bare wires, burn marks, or melted plastic. Separate the connector and carefully inspect the terminals (the metal parts) inside the connector. See if they look burned or have a green tint indicating corrosion, especially if they are mounted outside the transmission case. Use electrical contact cleaner and a plastic bristle brush if cleaning the terminals is necessary. Allow to dry and apply electrical grease where the terminals make contact.
If you have a scan tool, clear the diagnostic codes from memory and see if the P083A code returns. If not, the connections were likely your problem.
This is the most common area of concern for this code, as external transmission connections have the highest incidence of corrosion problems.
If the P083A code returns, we will need to test the TFPS sensor and its associated circuits. With the key off, disconnect the electrical connector from the TFPS sensor. Connect a black wire from the digital voltmeter (DVOM) to the ground or low reference terminal at the TFPS sensor harness connector. Connect the red wire from the digital voltmeter to the signal terminal of the TFPS sensor harness connector. Turn the key to the engine off position. Check manufacturer specifications; the voltmeter should read 12 volts or 5 volts. Wiggle the connections to see if they change. If the voltage is incorrect, repair the power or ground wire or replace the PCM/TCM.
If the previous test was successful, connect one wire of an ohmmeter to the signal terminal of the TFPS sensor and the other wire to the ground or low reference terminal of the sensor. Check manufacturer specifications for sensor resistance to accurately test resistance to pressure when no pressure is applied to it. Wiggle the transmission fluid pressure sensor/switch connector while monitoring the resistance. If the ohmmeter readings do not pass, replace the TFPS.
If all previous tests have passed and you continue to get a P083A, this would most likely indicate a faulty TFPS sensor, although a faulty PCM/TCM cannot be ruled out, nor internal transmission malfunctions until the TFPS sensor has been replaced. When in doubt, seek help from a qualified automotive diagnostician. PCMs/TCMs must be programmed or calibrated to the vehicle in order to be installed correctly.