What does it mean?
This is a generic powertrain diagnostic trouble code (DTC) that applies to many OBD-II vehicles (1996-newer). This may include, but is not limited to, vehicles from Chrysler, Ford, Jeep, General Motors, Dodge, Chevrolet, Mercedes, etc. Although generic, the exact repair steps may vary depending on the year, make, model, and powertrain configuration.
The OBD-II fault code P0839 and related codes P0836, P0837, and P0838 are associated with the four-wheel drive (4WD) switch circuit. This circuit is also known as the transfer case control circuit.
The purpose of the four-wheel drive switch circuit is to allow the driver to select the activation of the four-wheel drive system and change the transfer case gear ratios between two-wheel high, two-wheel low, neutral, four-wheel high, and four-wheel low as needed based on the configuration.
When the PCM or TCM detects a voltage or resistance that is too high above the expected normal range in the 4WD switch circuit, code P0839 is set, and the check engine light, 4WD malfunction light, or both may illuminate.
How severe is this DTC?
The severity of this code is normally moderate, but four-wheel drive switch circuit issues can be serious if the transfer case is stuck in low gear, causing unwanted strain on the internal transmission and engine components requiring immediate attention. In some circumstances, the vehicle may not move or shift gears at all.
What are some of the symptoms of the code?
Symptoms of a P0839 fault code may include:
- Transfer case stuck in one gear
- The vehicle will not engage at all
- Transmission shifts harshly
- 4×4 malfunction light illuminated
- Check engine light illuminated
What are some of the common causes of the code?
Causes of this P0839 code may include:
- Faulty four-wheel drive switch
- Malfunctioning transfer case
- Defective or damaged wiring
- Loose or faulty control module ground strap
- Corroded, damaged, or loose connector
- Faulty fuse or fusible link (if applicable)
- Faulty PCM or TCM
What are the troubleshooting steps for P0839?
The first step in the troubleshooting process for any malfunction is to search for Technical Service Bulletins (TSBs) for the specific vehicle by year, model, and powertrain. In some circumstances, this can save a lot of time in the long run by pointing you in the right direction.
The second step is to check the transmission and transfer case fluid to verify its condition and confirm it is at the appropriate level. Then locate all components associated with the 4WD switch circuit and look for obvious physical damage. Based on the specific vehicle, this circuit may integrate several components, including the transfer case, switches, solenoids, PCM, and TCM. Perform a thorough visual inspection to ensure the associated wiring has no obvious defects such as scraping, rubbing, bare wires, or burn marks. Next, check the connectors and connections for security, corrosion, and damaged pins. This process must include all wiring connectors and connections to all components, including the PCM and TCM. Consult vehicle-specific technical data to verify the configuration and see if a fuse or fusible link is incorporated into the circuit.
Advanced Steps
Advanced steps become very vehicle-specific and require appropriate advanced equipment to operate accurately. These procedures require a digital multimeter and vehicle-specific technical references.
Voltage Checks
Reference voltage and acceptable ranges may vary depending on the specific vehicle and circuit configuration. Specific technical data will include troubleshooting charts and the proper sequence to follow to help you make an accurate diagnosis.
If this process identifies the absence of a power source or ground, continuity tests may be required to verify the integrity of the wiring, connectors, and other components. Continuity tests should always be performed with the power disconnected from the circuit, and normal readings for wiring and connections should be 0 ohms of resistance. Resistance or lack of continuity is an indication of faulty wiring that is open or shorted and must be repaired or replaced. A continuity test from the PCM or TCM to the chassis will confirm the serviceability of the ground straps and wires. The presence of resistance indicates a loose connection or possible corrosion.
What are the common repairs for this code?
Replacing the 4×4 switch or solenoid
Cleaning corrosion from connectors
Repairing or replacing faulty wiring
Replacing a blown fuse or fusible link (if applicable)
Repairing or replacing faulty ground straps
Reprogramming or replacing the PCM or TCM
Common Mistake
Replacing the four-wheel drive switch or transfer case when faulty wiring is causing the PCM or TCM to set this code.
I hope the information in this article has been helpful in guiding you in the right direction to correct the issue with your 4WD switch circuit error code. This article is strictly informational, and the technical data and service bulletins specific to your vehicle should always take priority.