What Does It Mean?
This generic powertrain diagnostic trouble code (DTC) generally applies to all OBD-II equipped vehicles with a clutch pedal. This may include, but is not limited to, vehicles from Jaguar, Dodge, Chrysler, Chevy, Saturn, Pontiac, Vauxhall, Ford, Cadillac, GMC, Nissan, etc. Although generic, specific repair steps may vary by make/model.
The OBD-II fault code P0835 is associated with the “B” circuit of the clutch pedal switch. When the Powertrain Control Module (PCM) detects a malfunction in the “B” clutch pedal switch circuit, also referred to as the clutch position sensor or clutch start switch circuit, a number of different codes can be set.
These codes are P0830, P0831, P0832, P0833, P0834, P0835, and P083F depending on the specific malfunction that alerts the PCM to set the code and illuminate the Check Engine light.
The “B” clutch pedal switch circuit functions to monitor the position of the clutch pedal. This process is accomplished by reading the output voltage from the clutch position sensor. The clutch position sensor switch design can vary from one vehicle to another; it is typically a basic “on/off” switch mounted near the clutch pedal on the bracket. Regardless of design, a constant voltage is typically present on one side of the switch, and the contacts are closed by engaging the clutch pedal to transfer voltage to the starter or starter solenoid. This basic circuit and switch prevent the engine from starting before the clutch is engaged.
Code P0835 Clutch Pedal Switch Circuit B High is set by the PCM when the “B” clutch pedal switch circuit experiences a high voltage situation. Refer to a vehicle-specific repair manual to determine which is the “B” circuit for your particular vehicle.
How Severe Is This DTC?
The severity of this code is normally moderate, but it can be severe if the vehicle starts with the clutch disengaged, creating a safety issue.
What Are Some of the Symptoms of the Code?
Symptoms of a P0835 engine code may include:
Engine does not start
Engine starts without engaging the clutch
Check Engine light illuminated
What Are Some of the Possible Causes of the Code?
-
Causes
of this code may include:
- Faulty clutch position sensor switch
- Blown fuse or fuse link (if applicable)
- Corroded or damaged connector
- Faulty or damaged wiring
- Faulty PCM
What Are the P0835 Troubleshooting Steps?
The first step in the troubleshooting process for any malfunction is to research the Technical Service Bulletins (TSBs) for the specific vehicle by year, model, and powertrain. In some circumstances, this can save a lot of time in the long run by pointing you in the right direction.
The second step is to locate the clutch position sensor switch and look for obvious physical damage. Perform a thorough visual inspection to check that the associated wiring does not have obvious defects such as scraping, rubbing, bare wires, or burn marks. Then, check the connectors and connections for security, corrosion, and damaged pins. This process should include all wiring connectors and connections to the clutch position sensor switch, PCM, starter, and starter solenoid. Consult vehicle-specific technical data to see if a fuse or fuse link is incorporated into the circuit.
Advanced Steps
Advanced steps become very vehicle-specific and require appropriate advanced equipment to perform accurately. These procedures require a digital multimeter and vehicle-specific technical references. Voltage requirements will be highly based on the specific year and model of the vehicle.
Voltage Checks
When the clutch is disengaged, there should be an appropriate 12-volt voltage on one side of the switch. When the clutch is engaged, you should have voltage on both sides of the switch. The starter solenoid or starter should also be powered depending on the configuration.
If this process identifies the absence of a power source or ground, continuity tests may be required to check the integrity of the wiring and the clutch position sensor switch.
When the clutch is engaged, you should have continuity through the switch, and when the clutch is released, the meter should indicate no continuity through the switch. Continuity tests should always be performed with the power disconnected from the circuit, and normal readings for wiring and connections should be 0 ohms of resistance, unless otherwise indicated by technical data. Resistance or lack of continuity is an indication of faulty wiring that is open or shorted and must be repaired or replaced.
What Are the Common Repairs?
- Replacing the clutch position sensor
- Replacing a blown fuse or fuse link (if applicable)
- Cleaning corrosion from connectors
- Repairing or replacing wiring
- Programming or replacing the PCM
Common Mistakes
Replacing the starter or solenoid when the clutch position sensor, damaged wiring, or a faulty connector is the cause.
I hope the information in this article has been helpful in guiding you in the right direction to correct the issue with the “B” clutch pedal switch circuit fault code. This article is strictly informational, and specific technical data and service bulletins for your vehicle should always take priority.